Search by criteria

EBOLIT 511

used for preparation of floorings, polymer mortars, polymer concretes, sealants, swabbing masses and laminates

Product characteristics

Solution of low molecular weight epoxy resin in organic diluent. Applications EBOLIT 511 is intended for penetration and impregnation of porous materials (such as concrete, wood, paper etc.). Penetration mixture is prepared by thorough mix of EBOLIT 511 and a HARDENER. EBOLIT 511 should be applied solely to a clean surface void of lipoid and mechanical impurities. Depending on quality of the surface, the coating is applied in one or multiple layers. When penetrating a concrete surface (which must comply with ČSN 74 4505) to apply cast flooring or polymer concrete, varnish coat must not be created. Penetration is applied until the concrete base reaches its unabsorbability.

Product Features

Colourless to light yellow coloured low-viscous liquid with a characteristic smell that is non-miscible with water. The agent can be diluted by acetone, toluene or butyl acetate.

Organic solvent content

characteristic 

unit

value

product's density

g.cm-3

0.980

Content of organic solvents (expressed in mass fraction)

kg/kg of the product

0.50

Total organic carbon content

kg/kg of the product

0.310

Content of nonvolatile substances (expressed in volume percent)

volume percent

36.7

EBOLIT 511 must comply with the following quality characteristics:

Quality characteristic 

Value

Methodology of assessment

Content of nonvolatile substances (%)

50 ± 3.0

PN-ZM 525/2009

Epoxy equivalent in dry matter (g.mol-1)

maximally 188.5

ČSN EN ISO 3001

Epoxy index in dry matter (mol/1000 g)

minimally 5.3

ČSN EN ISO 3001

 For application purposes, EBOLIT 511 is hardened by the following hardeners (indicated for 100 units of mass of EBOLIT 511):

HARDENER P11                                  

6.3 units of mass

HARDENER T 410                                

11.5 units of mass

HARDENER P22                       

11.5 units of mass

HARDENER MK                        

16.5 units of mass

Surface preparation

A surface on which penetration coating is applied must be void of all mechanical impurities, oil and grease stains as well as other impurities that could negatively affect agent's adhesive properties. The surface can be sandblasted, singed, milled or abraded.

Directions for Use

EBOLIT 511 in a form of a penetration varnish is obtained by thorough mixing both components (EBOLIT 511 and a hardener). Lifespan of a resin hardener composition is approximately 24 hours. The penetration coating can be applied by one of common coating methods - brushing (using a brush or tar brush), spraying, dipping etc. Minimal temperature for applying the penetration coating is 15 °C. At lower temperatures, hardening time extends. It takes up to 24 hours under standard conditions at 20 °C. When applying the agent, we care that the underlying material is saturated and, at the same time, that dry varnish coat is not formed on its surface. Usually, a single layer of this coating is sufficient. Tools used during application of the product should be washed and cleaned by organic diluent (e.g. acetone, toluene, butyl acetate) immediately after the work is finished.

EBOLIT 511 Usage:  Usage of an EBOLIT 511 composition for concrete ranges from 300 to 800 g.m-2 for a single coating.

Packaging & Storage

EBOLIT 511 is delivered in 200 l metallic barrels. Alternatively, it can be delivered in different containers that were discussed and agreed on in advance. Store it in a sealed container in places protected from direct climatic influences. Recommended storage temperature is between +5 to +30 °C. Must not be stored in the sun or near heat sources. Storing at temperatures below 0 °C does not affect product's application properties.

Transport

EBOLIT 511 is transported in compliance with ADR/RID Regulations.

 Warranty

Provided the product is transported and stored in accordance with the above written conditions, its warranty is 6 months from the production date.

Note

Data about the product characteristics and its processing were obtained by laboratory measurements and application tests. This technical data sheet can provide solely legal advice without any engagements. Use of the product should be always adjusted to specific conditions.

 

Purpose of usebonding primer products in construction industry
Propertiestwo-component organic coating, bonding primer of concrete, interior application, dilutable coatings
 
lrqa.cz schp.cz urs-czech.cz mpo.cz